Delrin and Aluminum Steering Rack Bushings

[Gun_Runner]

Hey guys,
I am now going to be machining both Delrin and solid aluminum steering rack bushings for the Fiesta and Fiesta ST! These have been a big hit for the Mk 1 and Mk 2 Focus, and pretty significantly increase steering control and response. It also forces the wheels to stay where you are pointing them, instead of being able to push against the rubber and twitch around turns, as well as immediately going where you point them, instead of loading against the rubber, and then finally unloading in that direction.

These work by replacing the squishy rubber bushings that the factory installs with Delrin, which is a very stiff and exremely durable acetal resin plastic. I finish it off with a steel center sleeve to prevent over compression.

I also make them from solid aluminum for the ultimate stiffness and durability, but you might experience extra harmonic vibration through the steering wheel.

Aluminum - $55 shipped
Delrin - $65 shipped

Please PM me if interested. Also, go check out my other sites!

Alexthemachinist.com
Facebook.com/alexthemachinist

Thanks,
Alex Gaebel
Monrovia, CA 91016

(626) 203-2058
Alexthemachinist@gmail.com

INSTALLATION INSTRUCTIONS
http://www.fiestastforum.com/forum/threads/7232-Steering-Rack-and-Bushing-Install-Instructions

 

[RAAMaudio]

Damn nice mod and one I most highly endorse

I will order as soon as you let me know how and I am ready for a shipping address as will be in a two different big states withing the next ten days or so.

I trimmed down some washers to fit over the stock bushings to tighten them up a as much as I could but solid bushings are much better and I will use the Delrin as over the long haul will last longer than aluminum.

 

[Hijinx]

I'll keep these in mind.

 

[Gun_Runner]

Damn nice mod and one I most highly endorse

I will order as soon as you let me know how and I am ready for a shipping address as will be in a two different big states withing the next ten days or so.

I trimmed down some washers to fit over the stock bushings to tighten them up a as much as I could but solid bushings are much better and I will use the Delrin as over the long haul will last longer than aluminum.

I'll pm you

 

[LT Berzerker]

Good I wish I had the cash... Maybe Santa will be kind

 

[D1JL]

Please follow the rules.

Classified Posts Requirements PLEASE READ AND FOLLOW

Photos with your Screen Name and Date included in picture as well as FiestaSTForum are required to prove that you own it.
You cannot photoshop your username onto the photo afterwards.
This is a form of "Buyer Protection".

Flash Devices:
Please note that we do not allow the sale of locked/married flash devices.
In order to list these devices for sale, you must provide proof that your device is unlocked/unmarried.
Failure to do so will result in your thread being deleted.
This means taking a photo of the device that shows the install or uninstall screen.


Your cooperation is appreciated.


This thread will be deleted if the rules are not complied with.


Dave

 

[Gun_Runner]

Please follow the rules.

Classified Posts Requirements PLEASE READ AND FOLLOW

Photos with your Screen Name and Date included in picture as well as FiestaSTForum are required to prove that you own it.
You cannot photoshop your username onto the photo afterwards.
This is a form of "Buyer Protection".

Flash Devices:
Please note that we do not allow the sale of locked/married flash devices.
In order to list these devices for sale, you must provide proof that your device is unlocked/unmarried.
Failure to do so will result in your thread being deleted.
This means taking a photo of the device that shows the install or uninstall screen.


Your cooperation is appreciated.


This thread will be deleted if the rules are not complied with.


Dave

Edited

 

[frankiefiesta]

PM'd

 

[RAAMaudio]

I just ordered the aluminum bushings as want the best feedback possible though delrin will be very close.

I also would not take the time to install such a part if I did not know it can make a significant improvement in feedback and precision at speed. I have done two Vettes with aluminum bushings that were very hard to get to, this car will be much easier, the effort on the Vettes was worth it and it will be on the FiST as well.

I have not installed steering rack bushings on an electric power steering system car before but I still expect it to help and electric systems need all the help they can get. We are lucky the system on our cars is pretty darn good, making it better will only enhance the fun

 

[Hijinx]

I just ordered the aluminum bushings as want the best feedback possible though delrin will be very close.

I also would not take the time to install such a part if I did not know it can make a significant improvement in feedback and precision at speed. I have done two Vettes with aluminum bushings that were very hard to get to, this car will be much easier, the effort on the Vettes was worth it and it will be on the FiST as well.

I have not installed steering rack bushings on an electric power steering system car before but I still expect it to help and electric systems need all the help they can get. We are lucky the system on our cars is pretty darn good, making it better will only enhance the fun

Can't wait to hear about it.

 

[Elwood125]

In for results [emoji16]

 

[InsTwin]

I'm interested but want to see some install instructions before pulling the trigger.

 

[Gun_Runner]

Hey guys, sorry it got locked for a bit. Hoping to get some more interest on here, so I can stick around.

 

[ChristianW]

I would be very interested as long as there is some info on how to install and its not too difficult!

 

[jeff]

Definitely interested. Can you post a link of install directions for the Focus so we can see what is involved? That will sway a lot of us I think.

 

[Gun_Runner]

I will try and get together some install instructions

 

[Chuckable]

Interested too, but like others, would like some more info. and instructions

 

[WhiteFords]

This sounds like a great modification. I am interested to hear about how the install goes.

 

[Motorstate]

I'd be interested in these as well baring ease of installation.

 

[Gun_Runner]

Here you guys go. I made a thread on how to install them, as well as remove the steering rack. Might be sticky worthy if no one has a how to yet.

http://www.fiestastforum.com/forum/threads/7232-Steering-Rack-and-Bushing-Install-Instructions